Polaroid TV DVD Combo FDM 0700A User Manual

7” Under-the-Counter LCD / DVD  
FDM-0700A  
Operating Manual  
 
Important Safety Instructions  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT  
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The lightning flash with arrowhead symbol, within an equilateral triangle,  
is intended to alert the user to the presence of uninsulated “dangerous  
voltage” within the product’s enclosure that may be of sufficient  
magnitude to constitute a risk of electric to persons.  
The exclamation point within an equilateral triangle is intended to alert the  
user to the presence of important operating and maintenance (servicing)  
instructions in the literature accompanying the appliance.  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,  
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.  
POWER SUPPLY:  
Connect the supplied adapter to the side of the DVD player in the slot marked “DC 12V  
IN”. Plug the two-prong end of the power cord to an AC100-240V outlet. If you have  
difficulty inserting the plug, turn it over and reinsert it, if the unit will not be used for a  
long time, disconnect the plug from the outlet.  
NOTE:  
Before plugging the power cord into an AC outlet, make sure that all the connections  
have been made.  
CAUTION:  
These servicing instructions are for use by qualified service personnel only. To reduce  
the risk of electric shock, do not perform any servicing other than that contained in the  
operating instructions unless you are qualified to do so.  
Refer to service manual for servicing instructions.  
 
-3-  
Important Safety Instructions  
Note:  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
IMPORTANT FOR LASER PRODUCTS  
1. CLASS 1 LASER PRODUCT  
2. DANGER: Visible laser radiation when open and interlock failed or  
defeated. Avoid direct exposure to beam.  
4. Follow all instructions.  
5. Do not use near water.  
6. Clean only with dry cloth.  
3. CAUTION: Do not open the top cover. There are no user service-  
able parts inside the unit. Leave all servicing to qualified service  
personnel.  
7. Do not block any ventilation openings. Maintain well ventilated conditions around  
the product. Do not put product on bed, sofa or anything that blocks ventilation.  
Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or  
other apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A  
polarized plug has two blades with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide blade or the third prong is  
provided for your safety. If the provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs,  
convenience receptacles, and the point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket, or table specified by  
the manufacturer, or sold with the apparatus. When a cart is used,  
use caution when moving the cart/apparatus combination to avoid  
injury from tip-over.  
13. Unplug this apparatus during lightning storms or when unused for long periods of  
time.  
14. Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not operate normally, or has  
been dropped.  
15. Apparatus shall not be exposed to dripping or splashing and no objects filled with  
liquids, such as vases, shall be placed on the apparatus.  
Copyright Protection  
Unauthorized copying, broadcasting, public performance, and lending of disks are  
prohibited. This product incorporates copyright protection technology that is protected  
by method claims of certain U.S. patents and other intellectual property rights owned  
by Macrovision Corporation and other rights owners. Use of this copyright protection  
technology must be authorized by Macrovision Corporation, and is intended for home  
and other limited viewing uses only unless otherwise authorized by Macrovision  
Corporation. Reverse engineering or disassembly is prohibited.  
 
-4-  
FCC Notice  
Note: This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installation.  
This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur  
in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the following  
measures:  
--Reorient or relocate the receiving antenna.  
--Increase the separation between the equipment and receiver.  
--Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
--Consult the dealer or an experienced radio/TV technician for help.  
 
-5-  
Characteristic Features  
This product incorporates  
a
DVD  
Advanced Playing Function  
Compatibility  
Plays: DVD, CD, CD-R, CD-RW, JPEG  
and MP3 discs.  
player, LCD display, TV receiver and  
radio function in one system. It is  
designed for convenient use in the  
kitchen. Please refer to page 32 for the  
installation instructions.  
On-Screen Display  
Displays your choice of English, Spanish  
or French.  
Multiple Mode  
Fast Search Function  
 
 
 
 
DVD  
Multi-speed, fast forward, fast reverse,  
slow play and repeat playback.  
Zoom Function  
TV  
Radio  
External Audio  
mode  
&
Video Input  
Allows the viewer to enlarge in the  
picture.  
Search By Time  
High Quality Property  
Video Screen  
Search for a certain time on a disc.  
Last Memory Playback  
Continues playback from a stopped point  
as long as power is applied to the DVD  
Player.  
Supports normal screen (4:3) and wide  
screen (16:9) aspect ratios.  
AV Input  
External AudioVideo input can be  
connected to most external AV sources.  
LCD (Liquid Crystal Display) screen  
Color video screen designed with LCD  
technology clearly shows video data.  
Amplifier Function  
TV Functions  
 
 
 
Clear TV signal reception.  
Search for TV channels automatically.  
Automatically memorize the channels.  
Built-in 2x2.5w stereo amplifier with left  
and right speakers.  
Radio Functions  
  Clear AM/FM signal reception.  
  Search for radio stations  
automatically.  
Switching Power Adapter  
Automatically adapts to the voltage  
required.  
Special Functions  
  Store radio stations easily.  
  Search for radio stations in high or  
low frequency range.  
Supports Multi-language and Parental-  
lock features.  
 
-6-  
Disc Information  
Disc Formats Supported By This Player  
PLAYBACK TIME/  
PLAYABLE SIDES  
DISC LOGO  
DIAMETER  
133 min (SS-SL)  
242 min (SS-DL)  
266 min (SS-SL)  
484 min (SS-DL)  
41 min (SS-SL)  
12cm  
DVD  
75 min (SS-DL)  
8cm  
82 min (DS-SL)  
150 min (DS-DL)  
12cm  
74 min  
CD  
8cm  
20 min  
MP3  
12cm  
600 min  
The disc maker specifies the operation of some DVD discs. Please refer to the  
instruction manual with the disc.  
Care of Discs  
Cleaning of Discs  
If a disc has fingerprints or dust on it,  
lightly wipe the disc with soft cloth from  
the center of the disc outward.  
Do not touch the playing surface of the  
disc.  
Do not stick paper or labels on the disc.  
Storage of Discs  
Do not expose discs to direct sunlight or  
excessive temperatures.  
Never use record cleaning sprays, or  
any other solvents to clean your discs.  
 
Front Panel  
Front Panel Drawing  
1. POWER button  
Press twice to go to the previous  
track/chapter.  
Press to enter or exit the STANDBY  
mode.  
7. SOURCE button  
2. PLAY/PAUSE button  
Press to start or pause playback under  
DVD mode.  
Press to shift among DVD, TV,AV,FM  
and AM mode.  
8. EJECT button  
3. Disc Tray  
Press to open or close the disc tray.  
9. Remote Sensor  
Used to load disc.  
4. STOP button  
Receives remote control signal for  
operation.  
Press to stop playback under DVD mode.  
5.  
10. Display panel  
Press to go to the next track under DVD  
mode.  
Displays the time, status, radio  
frequency and radio station number.  
When adjusting volume, the VOL and  
volume level will be displayed on the  
display panel for several seconds.  
6.  
Under DVD mode, press once to go to  
beginning of the current track/chapter.  
 
- 8 -  
Front Panel  
11. SEEK –/+ button  
16. ▲  
Under radio mode, press once to fine  
tune frequency backward or forward.  
Press for about 1.5 seconds to search  
radio stations backward or forward  
automatically.  
Press to select items in the setup menu.  
Press to select channels or radio  
stations forward under TV or radio mode.  
Press to adjust the value upward when  
setting the time on the display panel.  
17. OK button  
Under DVD mode, press to activate fast  
backward or forward playback.  
12. MUTE button  
Press to confirm selections in setup  
menu.  
Press to turn the speaker output on or  
off. The corresponding information will  
be displayed on the display panel.  
13. SET button  
18.  
Press to select items in the setup menu.  
Press to increase the volume. Press to  
increase the value in the picture setup  
menu.  
Press to enter and exit from the timer  
setup menu. Press to memorize the  
station under AM/FM status.  
19. ▼  
Press to select items in the setup menu.  
Press to select the channels or radio  
stations backward under TV or radio  
mode.  
14. TIME button  
Press it once to display the time on the  
display panel. In standby status, the time  
is still displayed on the panel.  
Press it again to set the time on the  
display panel. Use the ꢂꢃbuttons to  
select the editing position of hour or  
minute, and then use the ꢄꢅ buttons to  
adjust the value of the hour or minute  
upward and downward.  
Press to adjust the value downward  
when setting the time on the display  
panel.  
20. TV/LCD SETUP button  
Press to enter the TV/LCD setup menu.  
21. LCD screen  
Presents a high resolution picture.  
15.  
Press to select items in the setup menu.  
Or press to decrease the volume. Or  
press to decrease the value in the  
picture setup menu.  
 
- 9 -  
Rear Panel and display panel  
Rear Panel Drawing  
1. ANT INPUT jack  
4. Left/Right AUDIO input jack  
Connected to external antenna to  
receive the TV program in TV mode.  
2. FM 75Ωcoaxial antenna jack  
3. AM antenna jack  
Connection for audio input.  
5. VIDEO input jack  
Connection for video input.  
6. Direct current 12V input jack  
Display Panel Drawing  
1. FM radio status indicator  
2. AM radio status indicator  
AM time indicator  
5. Minute or character indicators  
6. Character indicators  
7. FM frequency unit of MHz indicator  
3. PM time indicator  
4. Hour or character indicators  
8. AM frequency unit of KHz indicator  
 
- 10 -  
Remote Control  
Preparation  
Using Of Remote Control  
Refer to the drawing and remove the  
empty battery receptacle.  
Point the remote control towards the  
main unit when operating. The r/c works  
best at a distance less than 7m and at  
an angle of up to 60°to the front of the  
unit. No obstacles may stand in the way  
between r/c and infrared sensor.  
Insert the battery into the receptacle.  
Make sure the polarity matches the  
marks inside the component.  
The batteries normally last for about six  
months. This depends on how often and  
for what operations the remote control is  
used.  
Insert the receptacle into the remote  
control.  
If the remote control unit fails to work  
even when it is operated near the player,  
replace the batteries.  
If the r/c is not used for a long period of  
time, please remove the batteries from  
the compartment, to prevent damage by  
leakage.  
 
- 11 -  
Remote Control  
Remote Control Drawing  
 
- 12 -  
Remote Control  
1. POWER button  
11. SEEK – button  
Press to access to or exit the STANDBY  
mode.  
Under radio mode, press once to fine  
tune frequency backward. Press for  
about 1.5 seconds to search radio  
stations backward automatically.  
Under DVD mode, press to activate fast  
backward playback.  
2. SUBTITLE button  
Press to select a subtitle language or to  
turn subtitles off when a DVD with multi-  
subtitles is playing.  
12. SEEK + button  
3. DVD button  
Press to enter DVD mode.  
Under radio mode, press once to fine  
tune frequency forward. Press for about  
1.5 seconds to search radio stations  
forward automatically.  
4. TV button  
Press to enter TV mode.  
Under DVD mode, press to activate fast  
forward playback.  
5. AV button  
Press to shift to external AV input mode.  
13. PLAY button  
Press to start playback under DVD mode.  
6. FM/AM button  
Press to shift to FM/AM signal input  
mode.  
14. STOP button  
Press to stop playback under DVD mode.  
7. TV/LCD SETUP button  
Press to enter the TV/LCD SETUP menu.  
15. TITLE button  
Press to display titles if present on the  
disc under DVD mode.  
8. OK button  
Press to confirm selections.  
16. MENU button  
Press to access the disc menu under  
DVD mode.  
9. ꢂꢃꢄꢅ  
Press to select menu items or settings.  
Press ꢂꢃ buttons to adjust volume. Or  
press to adjust value in the picture setup  
menu.  
Press ꢄꢅ buttons to select channels or  
radio stations forward and backward in  
TV or radio mode. Or press to adjust the  
value of time when setting time on the  
display panel.  
17. REPEAT button  
Press to repeat a title, chapter, title or  
the entire disc.  
18. A-B Repeat button  
Used to play a section of the DVD from  
point “A” to point “B”. Press once to  
select the starting point (A) press again  
to select the end point (B). Press a third  
time to stop the A-B Repeat.  
10. SET button  
Press to enter and exit from the timer  
setup menu. Or Press to memorize the  
station under AM/FM status.  
 
- 13 -  
Remote Control  
19. EJECT button  
28. TIME button  
Press to open or close the disc tray.  
Press it once to display the time on the  
display panel. In standby status, the time  
is still displayed on the display panel.  
Press it twice to set the time on the  
display panel. Use the ꢂꢃbuttons to  
select the editing position of hour or  
minute, use the ꢄꢅ buttons to adjust  
the value of the hour or minute upward  
and downward.  
20. AUDIO button  
Press to access various audio languages,  
when the DVD disc contains multiple  
audio languages.  
21. 0-9 number buttons  
Select numbers by pressing these  
buttons.  
29.  NEXT button  
Press to go to the next track under DVD  
mode.  
22. GOTO button  
Press to select the desired disc starting  
Time, Track or Title.  
30.  PREV button  
23. +10 button  
Under DVD mode, press to go to  
beginning of current track or chapter.  
Press twice repeatedly to go to  
beginning of a previous track or chapter.  
Select numbers greater than 9 by  
pressing the (+10) button first, and then  
additional number buttons as needed.  
24. 16:9/4:3 button  
31. MUTE button  
Press to shift the aspect radio between  
16:9 and 4:3.  
Press to turn on/off the speaker output.  
The corresponding information will be  
displayed on the display panel.  
25. DVD SETUP button  
Press to access the DVD setup menu  
under DVD mode.  
32. PAUSE button  
Press to pause playback in DVD mode.  
26. INFO button  
33. ZOOM button  
Press to display detailed playback  
information.  
Press repeatedly to display additional  
information or to turn the information  
display OFF.  
Press to enter and cycle through zoom  
functions, use the direction buttons to  
pan around the screen.  
34. VOL/-  
Press to increase or decrease the  
speaker volume level.  
27. LCD ON/OFF button  
Press to turn the LCD screen display on  
or off under TV, AV and DVD mode.  
35. SLOW button  
Press to activate slow forward playback.  
 
- 14 -  
System Connections  
Do not connect the power cord until all other connections have been made.  
Each time you restart the unit, it remembers the last function used.  
Connecting To External AV Signal Source  
Connections should be made as follows:  
Connecting To TV Signal Input Source  
 
- 15 -  
System Connections  
Connecting To Antenna  
Connect the supplied AM/FM antennas to listen to the radio.  
In order to improve the signal, move AM loop antenna away from system and other  
equipment.  
Extend FM antenna fully.  
Keep the FM antenna as horizontal as possible after connection.  
When connecting the supplied AM loop antenna, connect two black cords to AM and  
ground jacks as shown below.  
If the FM reception is poor, use a 75Ωcoaxial cable (not supplied) to connect  
system to an outdoor FM antenna as above.  
If you connect the system with outdoor FM antenna, you should earth the system in  
order to avoid lightning strike.  
Do not connect the earth wire to gas pipe to prevent gas explosion.  
 
- 16 -  
System Connections  
Connecting To the Power Adapter  
This unit is powered via the switching power adapter (supplied). See the below figure for  
details:  
1. Connect the AC adapter to jack marked with “DC 12V IN” on the rear panel of the unit.  
2. Plug the two-prong end of the power cord to the grounded electrical socket.  
3. When not using the unit, turn off the power of the unit first, and then unplug the power  
supply to prevent malfunctions.  
 
- 17 -  
Radio Function  
Radio Function Operation  
Press the AM or FM button on the remote control or front panel to enter AM or FM radio  
mode. Then press the SEEK+/- button for about 1.5 seconds on the remote control or  
front panel to start searching forward/backward from the current frequency. Press the  
SEEK+/- button again to stop searching. Radio frequency will be displayed on the  
display panel. The frequency range of FM is from 87.5MHz to 107.9MHz, frequency  
range of AM is from 520kHz to 1710kHz.  
Fine Tuning  
Press the SEEK+/- button on the remote control or front panel once to fine tune the  
frequency forward/backward under radio mode.  
Semi-memorizing radio stations  
If you like a radio station and want to store it for later listening, press the SET button to  
memorize it. “SAVE X X” will be displayed on the display panel, “X X” represents the  
default station number.  
There are two methods to organize the memorized stations:  
Use the ꢄꢅ buttons to adjust the channel number for your preference, and then  
press the SET button again, the station will be memorized with the coded station  
number.  
Press the SET button again, the station will be automatically memorized with the  
default station number in sequence.  
You can store radio stations from 0 to 19, total 20FM or 20AM radio stations. If no  
buttons are pressed within 3 seconds of pressing the SET button first time, the  
frequency will appear on the display panel again, and the station will not be stored.  
Accessing memorized radio stations  
Press the number buttons on the remote control to access a radio station by its  
memory location code.  
Press the ꢄꢅbuttons on the remote control or front panel to select the radio  
stations forward and backward.  
When selecting the stations, the “CH XX” will appear on the display panel, where the  
“XX” is the channel number of the stored radio station. After a few seconds, the “CH XX”  
disappears and the radio frequency will be displayed once again.  
 
- 18 -  
TV Function  
Basic Operation  
Connect the antenna to the antenna jack on the rear panel. After connecting the  
antenna, connect the power supply cord. If the player is in standby mode, press the  
POWER button on the front panel to turn on the power.  
Press the TV button on the remote control to shift to TV mode.  
Press the ꢄꢅ buttons on the remote control, or use the number buttons directly, to  
select the desired channel.  
Some preferences can be preset:  
Picture Parameter Setup  
Press the TV/LCD SETUP button once on the remote control to enter PICTURE setup  
menu, and screen display as shown:  
PICTURE  
Brightness  
Contrast  
Color  
11  
13  
14  
Language  
Reset  
English  
EXIT  
TV SETUP  
Use the buttons to select the item you want to set (Brightness, Contrast, Color).  
Use the , buttons to adjust, you can adjust the items between 0 and 20.  
Use the , buttons to select the Language, press the , buttons to select English,  
French or Spanish.  
To restore a setting to the original value, use the buttons to select Reset, then  
press the OK button to confirm the change.  
Press the button on the remote control to exit from the setup menu.  
Press the button on the remote control to enter TV Setup menu.  
TV System Setup  
When the button is pressed, the TV system setup menu will appear:  
TV SETUP  
Signal  
CATV  
Channel  
Skip  
002  
ON  
Fine Tuning  
Auto Memory  
PICTURE  
EXIT  
 
- 19 -  
TV Function  
Use the buttons to select the item you want to set.  
Use the , buttons to select the item and enter it.  
Press the button on the remote control to exit from the setup menu.  
Press the button on the remote control to return to the picture setup menu.  
Signal  
Use the direction button to select CATV TV signal input mode.  
Use the direction button to select AIR TV signal input mode.  
Channel  
Use the , buttons to change the channel. In CATV input mode, you can select  
channels from 2 to 125; in AIR input mode, you can select channels from 2 to 69.  
Skip  
When the button is pressed to turn the function ON, it will skip the current channel  
when using to select channels.  
When the button is used to turn the function OFF, it will play the channels in  
sequence when selecting under normal playback status.  
Fine Tuning  
Use the buttons to select Fine Tuning, and then press the , buttons to tune  
forward or backward from the current channel  
Auto Memory  
Use the buttons to select Auto Memory, press the OK button to enter auto  
memory mode:  
SEARCHING  
CH009  
EXIT◄  
----------------------------  
 
- 20 -  
TV Function  
The auto memory will take a few minutes. The unit will search channels from the lowest  
channel to the highest channel in the standard channel list. When tuning operations are  
complete the unit will exit and store the channels by sequence in the memory.  
During tuning, press the button to exit the auto memory.  
Use the direction buttons to select the desired channel from those in memory.  
Timer Setup  
Press the SET button on the remote control to enter Timer setup menu, the screen will  
display as below:  
TIMER SET  
Timer  
OFF  
_ _: _ _ am  
_ _: _ _ am  
CATV  
Power on  
Power off  
Signal  
Channel  
002  
Exit: SET  
Use the buttons to select the item you want to set.  
Use the , buttons to enter the item and to select.  
Press the SET button again on the remote control to exit from the setup menu.  
Timer  
Use the , direction buttons to select ON or OFF. This function allows you to set the  
start time and end time of the desired signal source. No matter what mode the unit is in,  
this function will automatically start the playback of the desired signal source.  
Select ON to activate the function; select OFF to disable the function.  
Power on  
To set the playback start time of the signal source, use number buttons to input the  
desired start time in sequence of hour, minute. Press the , direction buttons to shift  
between am and pm.  
 
- 21 -  
TV Function  
Power off  
To set the playback end time of the signal source, use number buttons to input the  
desired time in sequence of hour, minute. Press the , direction buttons to shift  
between am and pm. When the playback of the signal source is over, the player will  
enter standby mode.  
Signal  
Use the , direction buttons to select CATV, AIR, FM or AM.  
Channel  
Use number buttons to input the desired TV channels. In CATV signal input mode, there  
are 124 channels to choose from (2-125); in AIR signal input mode, there are 68  
channels to choose from (2-69).  
Press the ꢄꢅ buttons on the remote control to select the desired channel, or use the  
number buttons to input and then press the OK button to confirm.  
Note:  
The function is active as long as the unit is continuously supplied with power. The unit  
will automatically play the selected input signal at the set start time and enter standby  
mode at the set end time each day.  
 
- 22 -  
AV Function  
AV Function  
The player has an additional AV input so it can function as a monitor for a DVD player,  
video cassette player, satellite receiver, video game, etc. When an AV source is  
connected, press the AV button on the remote control to enter external input AV mode.  
Picture Parameter Setup  
Press the LCD SETUP button once on remote control to enter PICTURE setup menu,  
and screen will display as shown:  
PICTURE  
Brightness  
Contrast  
Color  
11  
13  
14  
Language  
Reset  
English  
Exit  
Use the buttons to select the item you want to set (Brightness, Contrast, Color).  
Use the , buttons to adjust the items between 0 and 20.  
Use the , buttons to select the Language, press the , buttons to select English,  
French or Spanish.  
Select Reset to return to the factory default settings.  
Press the button on the remote control to exit from the setup menu.  
Note:  
Under AV mode, if there is no signal, the LCD screen will be turned off automatically.  
When connected to an AV signal source, make sure the type of the selected AV signal  
source is NTSC.  
 
- 23 -  
Play Operation  
Preparation  
1. Install the unit in the kitchen; refer to page 32 for details.  
2. After connecting the unit to the AC power, turn on the unit’s power by pressing the  
POWER button on the front panel or the remote control.  
3. Press the DVD button on the remote control or the SOURCE button to shift to DVD  
mode.  
4. Press the EJECT button on the front panel or the remote control to open the disc  
tray.  
5. Load the disc with the label facing up.  
6. Press the EJECT button again to close the disc tray. The player will automatically  
search for the disc and start playback.  
DVD Playback  
Menu  
Normally there is a selecting menu for DVD discs. You can press the MENU button to  
enter the menu, and use the direction buttons to highlight an item you would like to  
select. Press the OK button to select it.  
Title & Chapter  
Normally there are several titles in a DVD disc, and several chapters (sections) in a title.  
You can select any title or chapter quickly by entering the relevant number.  
Audio  
DVD discs can contain up to 8 audio bit streams. For Example: English, Spanish,  
French etc.  
To select the audio bit stream you prefer press the AUDIO button on the remote control  
during playback. The DVD player will play the next audio bit stream every time you  
press the AUDIO button in succession.  
Note: This function is only available for discs that have several audio bit streams  
recorded onto it.  
 
- 24 -  
Play Operation  
Subtitle  
A DVD disc can be recorded with up to 32 subtitles.  
Press the SUBTITLE button on the remote control during playback to select the one you  
prefer.  
NOTE: This function is only available on DVD discs that are recorded with multi-  
subtitles.  
CD Playback  
The player will play all tracks on a CD disc by default. You can use the  and  
(PREV/NEXT skip) buttons, or number buttons to select a track.  
MP3 playback  
MP3 is an Audio compression format, which compresses the audio signal at the rate of  
12:1. When using the MP3 format, one disc can record more than 600 minutes of music,  
with sound quality that is similar to that of CD discs.  
There are many different methods for storing MP3 songs. Usually, one MP3 disc  
includes many folders (directories) and every folder includes several files (songs).  
Load a MP3 formatted disc into the DVD Player and a menu will be displayed on the  
screen. In stop status, press the up/down direction button to select the directory as you  
desire and press the OK or PLAY button for confirmation, use the up/down direction  
buttons again to select the desired track. In playback status, use the  or  button to  
select the next or previous track.  
During MP3 playback, press the previous or next button to turn the page.  
There is no search by time or slow playback function for MP3 discs.  
 
- 25 -  
Play Operation  
JPEG Playback  
JPEG is a common picture format that requires small amounts of storage per image and  
has low loss in resolution. Hundreds of pictures can be stored on a disc in this format. In  
order to view JPEG photo albums, you can ask your film development company to  
make a ”PICTURE CD” when they develop your film.  
Normal Playback  
Load a JPEG disc in. Use the OK button and Left/Right direction button to select a  
submenu with picture, and then use the Up/Down direction button to select the contents.  
Many discs have other contents besides pictures.  
Picture Rotation  
This can be used only when the picture is normally displayed. Once another picture is  
selected, rotation will be cancelled automatically.  
During playback, use the direction buttons to rotate the picture.  
Zoom and Move  
The ZOOM button is used to turn on/off the zoom and move functions.  
When this function is turned on, use the REV/FWD SCAN button to control zoom  
proportion and the TV screen will display the relevant proportion.  
When this function is turned off, the picture will resume normal size. Press the MENU  
button to return to menu page.  
Some JPEG discs may not support rotation or zooming functions.  
 
- 26 -  
Playback Functions  
Stop  
During playback, press the STOP button once on the remote control to stop playback of  
a disc. Press the PLAY button and the DVD Player will resume playback of the disc  
from the point where it was stopped.  
Pause  
Press the PAUSE button once on remote control or front panel to pause playback.  
Press the PLAY button to resume normal playback.  
Resume Playback  
Press the STOP button at the point if you wish to stop the playback of a disc. The DVD  
Player will memorize the location where playback of the disc was stopped.  
Press the PLAY button to resume normal playback. The DVD Player will resume the  
playback of the disc from the location where it was stopped. This function will not  
operate if the disc is removed from the DVD Player.  
Press the STOP button twice (2). Playback of the disc will stop. When the PLAY button  
is pressed again, playback of the disc will start from the beginning of disc.  
Zoom  
Press the ZOOM button on the remote control to cycle through the different zoom  
settings.  
Fast Playback  
Press the  or  button on the remote control to activate fast forward or rewind  
playback.  
Slow Playback  
Press the SLOW button to activate slow forward playback.  
There is no slow playback for MP3, CD discs.  
Search By Time  
During DVD disc playback, press the GOTO button on the remote control once, there  
will be a menu displayed on the screen. You can set or select items for your preference.  
Use the ꢄꢅ direction buttons to select items, press the OK button to enter and use the  
ꢄꢅ direction buttons to select the desired item. Press the direction button to return.  
When select the Title or Chapter, use number buttons to input desired title or chapter.  
Some DVD discs do not support the search function.  
 
- 27 -  
Playback Functions  
Previous and Next  
Press the PREV  button once to return to the currently playing Chapter or Track.  
Press the PREV button twice repeatedly and playback will start from the previous  
Chapter or Track.  
Press the NEXT  button on the remote control and playback of the disc will start from  
the next Chapter or Track.  
Repeat  
To repeat a Title, Chapter or Track press the REP button on the remote control.  
Continually pressing the REP button will display a menu as follows: Repeat Chapter,  
Title, All.  
You can temporarily select a section of a DVD that you would like to play repeatedly.  
You do this by marking the start and the end of the section using the A/B button. During  
playback press the A-B button on the remote control at the beginning of the segment  
(point A) you wish to play repeatedly. Press the A-B button again to mark the end of the  
segment (point B).  
The DVD player will automatically return to point A and repeat playback of the selected  
segment (A-B). To resume normal playback, press the A-B button again.  
Screen Mode  
Press the 16:9/4:3 button on the remote control to switch the screen aspect ratio  
between 16:9 and 4:3.  
 
- 28 -  
System Setup  
DVD Setup  
You can customize the set up menu to your own preference.  
Press the “DVD SETUP” button on the remote control to display the setup menu. The  
menu will include “General Setup”, “Speaker Setup”, “Dolby Digital Setup”, “Video  
Setup”, and “Preference Setup”. Press the direction button (ꢂꢄꢅꢃ) on the remote  
control to select a category. All the items in the category will appear on the screen.  
Press the “OK” button to enter the category.  
Category  
When you enter a category all the items under this category will appear, the highlighted  
category is the current set up.  
Press the right direction button () on the remote control to select another category  
(new selection will be highlighted). Press the “OK” button for confirmation.  
Press the left direction button () to enter the other setup menu(s).  
General Setup  
TV Display  
Select Normal/PS or Normal/LB when a 4:3 TV is connected.  
Select Wide when a 16:9 when using the screen on the unit or when a wide screen TV  
is connected to the video output.  
OSD Lang  
There are three different OSD languages for selection. You can select English, French  
or Spanish.  
Captions  
You can choose captions ON or OFF during playback.  
Screen Saver  
When activated, under stop mode, the unit will go into screen saver mode if the same  
image remains on the screen for several minutes, and then enter standby mode  
automatically.  
 
- 29 -  
System Setup  
Speaker Setup  
Downmix  
Select “LT/RT” in DOWNMIX, the player will output the audio signal IN MIXED NONO.  
Select “Stereo”, then the player will output a stereo signal.  
Dolby Digital Setup  
Dual Mono  
The function is used to select from stereo, left only, right only, and mixed mono.  
Dynamic  
Use this item to adjust linear dynamic compression rate to get different signal  
compression effects.  
Video Setup  
Sharpness  
Use this setting to adjust the sharpness level  
Brightness  
Use this setting to adjust the brightness level.  
Contrast  
Use this setting to adjust the contrast level.  
Preference Page  
Audio, Subtitle, Disc Menu  
This setting allows you to hear or read the subtitles of a DVD in your choice of English,  
Spanish and French etc. if the disc contains multiple languages.  
Parental  
DVD discs equipped with the child lock function are rated according to their contents  
and settings vary from disc to disc. Depending on the disc, you can lock out selected  
scenes or playback of the disc altogether. Access parental control by pressing the ꢄꢅ  
(direction buttons) on the remote control and then press the OK button.  
 
- 30 -  
System Setup  
Password  
Parental control features are password protected. The original setting is unlocked. This  
setting allows you to use number buttons to input any password.  
Note: The Default Password is 1369. This password is always effective even after you  
have selected your own password and changed it. To avoid the possibility of others  
using the default password to set the parental level and change the password, you can  
record this default password in another area and delete it from this manual. Some discs  
can be limited depending on the age of users while some discs cannot.  
Default Reset  
Use this function to reset all the settings.  
Note: For preference setting, the unit must be in the stop mode.  
LCD Setup  
Under DVD mode, press the LCD SETUP button on the remote control or front panel,  
there will be menu displayed on the screen.  
PICTURE  
Brightness  
Contrast  
Color  
11  
13  
14  
Language  
Reset  
English  
Exit  
Use the buttons to select the item you want to set (Brightness, Contrast, Color).  
Use the , buttons to adjust, you can adjust the items between 0 and 20.  
Use the , buttons to select the Language, press the , buttons to select English,  
French or Spanish.  
Select Reset to resume the original status.  
Press the button on the remote control to exit from the setup menu.  
 
- 31 -  
Installing the Unit In Kitchen  
Installing the unit under a cabinet  
The player unit may be installed in the kitchen with or without the spacer. The  
suggested mounting position of the unit is under a wall cabinet. See drawings below:  
NOTE: The dimensions of the player: 355mm x 75mm x 285 mm (W/H/D)  
There should be at least 35mm distance between the unit and the wall.  
Installing steps  
1. Mark the position of the 4 holes by using the supplied template. Drill four 6.5 mm  
diameter holes. As shown below:  
 
- 32 -  
Installing the Unit in Kitchen  
2. If the cabinet door overhangs the shelf and obstructs the unit, adjust the unit or the  
shelf height for clearance.  
3. Install the unit with the supplied mounting screws.  
4. There should be at least 35mm distance between the unit and the wall.  
Quick hints  
Since the unit is rather heavy, be careful while doing the fixing work.  
To reduce risk of fire, do not place any heating or cooking appliance beneath the unit,  
especially while the LCD screen is open on viewing.  
Mount the unit so that its AC power cord can be plugged directly to a wall outlet.  
Do not use a converter or extension cord.  
Be sure that the AC power cord has no slack when the player is working, because  
the cord acts as an FM wire antenna. If the AC power cord has some slack, wind it  
up to the cord hook until the cord has no slack.  
The unit has a built-in ferrite bar antenna for AM radio reception. Check the  
condition of AM reception before fixing in position.  
Install the unit as far as possible from a source of noise, for example, refrigerator,  
microwave oven, fluorescent lamp, etc.  
 
- 33 -  
Troubleshooting  
SYMPTOM  
CHECK ITEM  
Make sure a disc is loaded.  
Make sure the disc is loaded with label side up.  
Disc should be clean, not dirty or warped.  
Player’s region code should be the same as the region code  
of the DVD disc.  
The player cannot  
play.  
Make sure water condensation has not occurred. If it has,  
remove the disc and keep the player power on until the  
moisture evaporates.  
Make sure system connection is correct.  
Make sure the player is not under muting mode.  
Press the MUTE button to turn on the speaker.  
Make sure the volume is adjusted to the lowest.  
Adjust the volume upward.  
There is no sound.  
Is your disc dirty or warped? Clean or replace it.  
There is no picture  
or picture is  
unsteady. Position  
of the picture is  
incorrect.  
Make sure the video type of the AV signal source TV is  
NTSC.  
Make sure system connection is correct.  
Is your disc dirty or warped? Clean or replace it.  
Cannot continue to  
play and plays a  
section repeatedly.  
Make sure the player is not in A-B repeat status.  
Press A-B button to cancel A-B repeat status.  
Is your disc dirty or warped? Clean or replace it.  
Make sure there are no obstructions between the remote  
control and the player.  
Make sure the remote control is pointing at the player.  
Make sure batteries are inserted correctly (check polarity).  
Replace weak batteries.  
The remote control  
does not work.  
Other Notes: Static or other external interfere may cause the player to behave  
abnormally. If this occurs, unplug the power-supply cord from the outlet and plug it in  
again to reset the player. If the problems persist, then please disconnect the power and  
consult a qualified technician.  
 
- 34 -  
Specifications  
LCD screen size  
7 inches  
Laser Wavelength  
Video System  
Wavelength: 780/650nm  
NTSC  
Frequency Response  
Audio Signal-to-Noise  
Audio distortion + noise  
Channel Separation  
Dynamic Range  
20Hz20kHz ±2.5dB  
85 dB  
-70dB (1KHz)  
70dB (1KHz)  
80dB (1KHz)  
PLL  
System  
AM  
FM  
520~1710kHz  
Radio  
Frequency  
Range  
87.5~107.9MHz  
Power  
AC100V~ 240V, 50/60Hz  
Power Consumption  
25W  
Dimension  
Weight  
355mm X 75mm x 285mm (W/H/D)  
About 4 kg  
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE  
Manufactured under license from Dolby Laboratories.  
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.  
Confidential unpublished works. © 1992 -1997 Dolby Laboratories.  
All rights reserved.  
 
- 35 -  
the US call 1-866-289-5168, in Canada call 1-866-301-7922 and in Mexico call 01-800-  
400-2443.  
“Polaroid” is a registered trademark of Polaroid Corporation of Waltham, MA USA and  
licensed for use on the FDM-0700A to Petters Consumer Brands, LLC.  
 
- 36 -  

Peavey Musical Instrument Amplifier 112 212 Combo User Manual
Pelco Washer EM1109 User Manual
Pella Door V981553 User Manual
Pentair Swimming Pool Filter CFW Series User Manual
Philips Cordless Telephone DECT7272S User Manual
Philips Stereo Receiver US2 PH61150 User Manual
Philips TV Cables SGP9100 User Manual
Pioneer Portable DVD Player PDV 10 User Manual
Porter Cable Sander BN200SB User Manual
PYLE Audio Power Supply PINV5 User Manual