Polaroid Digital Camera CSGS15BC23 User Manual

CCD Camera  
GiantDragon B/W series  
CSGV90BC3  
CSGX36BC3  
CSGS20BC2  
CSGU15BC18  
CSGS15BC23  
Instruction Manual  
Thank you for purchasing our product.  
Before using this CCD Color Camera, please read through this instruction manual  
carefully in order to use this product correctly and safely.  
After reading, keep this instruction manual handy so that you can refer to, whenever  
you need it.  
Contents  
Safety Precautions  
1. Overview·····························································································1  
2. Features ·······························································································1  
3. Configuration ······················································································2  
4. Optional part························································································2  
5. Explanation rear panel·········································································3  
6. Connection ··························································································4  
7. Functions·····························································································5  
8. Timing chart ························································································8  
9. Troubleshooting··················································································10  
10. Specifications···················································································11  
11. Outline Drawing···············································································17  
Printed on recycled paper  
D4153659A  
 
[General Handing]  
WARNING  
! Stop operation immediately when any abnormality or defect occurs.  
If abnormal conditions are present, such as smoke, a burning smell, ingress of water or foreign  
matter, or if the equipment is dropped or malfunctions, fire or electric shock may result.  
Be always sure to disconnect the power cable from the wall socket at once and contact your  
dealer.  
Unplug  
! Do not use the equipment in locations subject to water splashes.  
Otherwise, fire or electric shock may result.  
Do not get wet  
Never pull apart  
! Do not disassemble, repair, or modify the equipment.  
Otherwise, fire or electric shock may result.  
For internal repair, inspection, or cleaning, contact your sales representative.  
! Do not place anything on the equipment.  
If metallic objects, liquid, or other foreign matter enters the equipment, fire or electric shock  
may result.  
Avoid  
Avoid  
! Do not install the equipment in an unstable or inclined location or locations subject to  
vibration or impact.  
Otherwise, the equipment may topple over and cause personal injury.  
! During an electrical storm, do not touch the power cable and the connection cable.  
Otherwise, an electric shock may result.  
Do not touch  
Instruction  
Avoid  
! Use the specified voltage.  
Use of an unspecified voltage may result in fire or electric shock.  
! Do not be handled roughly, damaged, fabricated, bent forcefully, pulled, twisted, bundled,  
placed under heavy objects or heated the power cable and the connection cable.  
Otherwise, fire or electric shock may result.  
D4153659A  
 
[General Handing]  
CAUTION  
! Observe the following when installing the equipment:  
· Do not cover the equipment with a cloth, etc.  
· Do not place the equipment in a narrow location where heat is likely to accumulate.  
Otherwise, heat will accumulate inside the equipment, possibly resulting in a fire.  
Instruction  
! Do not place the equipment in locations subject to high moisture, oil fumes, steam, or  
dust.  
Otherwise, fire or electric shock may result.  
Avoid  
Avoid  
! Do not install the equipment in locations exposed to direct sunlight or humidity.  
Otherwise, the internal temperature of the equipment will rise, which may cause a fire.  
! Use only specified the power cable and the connection cables.  
Otherwise, fire or electric shock may result.  
Instruction  
Instruction  
Avoid  
! When performing connection, turn off power.  
When connecting the power cable and the connection cable, turn off the equipment power.  
Otherwise, fire or electric shock may result.  
! Do not expose its camera head to any intensive light (such as direct sunlight).  
Otherwise, its inner image pickup device might get damaged.  
! Avoid short-circuiting signal output.  
Otherwise, a malfunction may occur.  
Avoid  
! Avoid giving a strong shock against the camera body.  
It might cause a breakdown or damage. If your camera is used in a system where its camera  
connector is subjected to strong repetitive shocks, its camera connector is possible to break  
down. If you intend to use your camera in such a situation, if possible, bundle and fix a camera  
cable in the place near the camera, and do not transmit a shock to the camera connector.  
Avoid  
! Contact your sales representative to request periodic inspection and cleaning (every  
approx five years).  
Accumulation of dust inside the equipment may result in fire or electric shock.  
For inspection and cleaning costs, contact your sales representative.  
Instruction  
D4153659A  
 
CASES FOR INDEMNITY (LIMITED WARRANTY)  
We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the user in  
the following cases.  
! In the case damage or losses are caused by fire, earthquake, or other acts of God, acts by a third party,  
deliberate or accidental misuse by the user, or use under extreme operating conditions.  
! In the case of indirect, additional, consequential damages (loss of business interests, suspension of business  
activities) are incurred as result of malfunction or non-function of the equipment, we shall be exempted from  
responsibility for such damages.  
! In the case damage or losses are caused by failure to observe the information contained in the instructions in  
this instruction manual and specifications.  
! In the case damage or losses are caused by use contrary to the instructions in this instruction manual and  
specifications.  
! In the case damage or losses are caused by malfunction or other problems resulting from use of equipment  
(connected equipments including Gigabit Ethernet Interface board, the lens, etc.) or software that is not  
specified.  
! In the case damage or losses are caused by repair or modification conducted by the customer or any  
unauthorized third party (such as an unauthorized service representative).  
! Expenses we bear on this product shall be limited to the individual price of the product.  
RESTRICTION FOR USE  
! Should the equipment be used in the following conditions or environments, give consideration to safety  
measures and inform us of such usage:  
1. Use of the equipment in the conditions or environment contrary to those specified, or use outdoors.  
2. Use of the equipment in applications expected to cause potential hazard to people or property, which  
require special safety measures to be adopted.  
! This product can be used under diverse operating conditions. Determination of applicability of equipment or  
devices concerned shall be determined after analysis or testing as necessary by the designer of such  
equipment or devices, or personnel related to the specifications. Such designer or personnel shall assure the  
performance and safety of the equipment or devices.  
! This product is not designed or manufactured to be used for control of equipment directly concerned with  
human life (*1) or equipment relating to maintenance of public services/functions involving factors of  
safety (*2). Therefore, the product shall not be used for such applications.  
(*1): Equipment directly concerned with human life refers to.  
· Medical equipment such as life-support systems, equipment for operating theaters.  
· Exhaust control equipment for exhaust gases such as toxic fumes or smoke.  
· Equipment mandatory to be installed by various laws and regulations such as the Fire Act or  
Building Standard Law  
· Equipment related to the above  
(*2) :Equipment relating to maintenance of public services/functions involving factors of safety refers to.  
· Traffic control systems for air transportation, railways, roads, or marine transportation  
· Equipment for nuclear power generation  
· Equipment related to the above  
D4153659A  
 
Notes on using this product  
! Handle carefully  
Do not drop the equipment or allow it to be subject to strong impact or vibration, as such action may cause  
malfunctions. Further, do not damage the connection cable, since this may cause wire breakage.  
! Environmental operating conditions  
Do not use the product in locations where the ambient temperature or humidity exceeds the specifications.  
Otherwise, image quality may be degraded or internal components may be adversely affected. In particular,  
do not use the product in areas exposed to direct sunlight. Moreover, during shooting under high  
temperatures, vertical stripes or white spots (noise) may be produced, depending on the subject or camera  
conditions (such as increased gain). However, such phenomena are not malfunctions.  
! Check a combination with the lens  
Depending on the lens and lighting you use, an image is reflected as a ghost in the imaging area. However,  
this is not because of a fault of the camera.  
In addition, depending on the lens you use, the performance of the camera may not be brought out fully due  
to deterioration in resolution and brightness in the peripheral area, aberration and others.  
Be sure to check a combination with the camera by using the lens and lightning you actually use.  
When installing a lens in the camera, make sure carefully that it is not tilted.  
In addition, use a mounting screw free from defects and dirt. Otherwise, the camera may be unable to be  
removed.  
! Do not shoot under intense light  
Avoid intense light such as spot lights on part of the screen because it may cause blooming or smears. If  
intense light falls on the screen, vertical stripes may appear on the screen, but this is not a malfunction.  
! Occurrence of moiré  
If you shoot thin stripe patterns, moiré patterns (interference fringes) may appear. This is not a malfunction.  
! Occurrence of noise on the screen  
If an intense magnetic or electromagnetic field is generated near the camera or connection cable, noise may  
be generated on the screen. If this occurs, move the camera or the cable.  
! Handling of the protective cap  
If the camera is not in use, attach the lens cap to the camera to protect the image pickup surface.  
! If the equipment is not to be used for a long duration  
Turn off power to the camera for safety.  
! Maintenance  
Turn off power to the equipment and wipe it with a dry cloth.  
If it becomes severely contaminated, gently wipe the affected areas with a soft cloth dampened with diluted  
neutral detergent. Never use alcohol, benzene, thinner, or other chemicals because such chemicals may  
damage or discolor the paint and indications.  
If the image pickup surface becomes dusty, contaminated, or scratched, consult your sales representative.  
! Disposal  
When disposing of the camera, it may be necessary to disassemble it into separate parts, in accordance with  
the laws and regulations of your country and/or municipality concerning environmental contamination.  
D4153659A  
 
Following information is only for EU-member states:  
The use of the symbol indicates that this product may not be treated as household waste. By  
ensuring this product is disposed of correctly, you will help prevent potential negative  
consequences for the environment and human health, which could otherwise be caused by  
inappropriate waste handling of this product. For more detailed information about the  
take-back and recycling of this product, please contact your supplier where you purchased the  
product.  
This equipment has been tested and found to comply with the limits for a class A digital device,  
pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause harmful interference to radio communication.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case  
the user will be require to correct the interference at his own expense.  
D4153659A  
 
环保使用期限标识,是根据电子信息产品污染控制管理办法以及,电子  
信息产品污染控制标识要求(SJ/T11364-2006)子信息产品环保使用期  
限通则,制定的适用于中国境内销售的电子信息产品的标识。  
电子信息产品只要按照安全及使用说明内容,正常使用情况下,从生产  
期算起,在此期限内,产品中含有的有毒有害物质不致发生外泄或突  
变,不致对环境造成严重污染或对其人身、财产造成严重损害。  
产品正常使用后,要废弃在环保使用年限内或者刚到年限的产品时,请  
根据国家标准采取适当的方法进行处置。  
10  
中华人民共和国  
环保使用期限  
另外,此期限不同于质量/功能的保证期限。  
The Mark and Information are applicable for People's Republic of China  
only.  
<产品中有毒有害物质或元素的名称及含量>  
有毒有害物质或元素  
部件名称  
六价铬  
Cr(VI))  
多溴联苯  
PBB)  
多溴二苯醚  
(PBDE)  
铅(Pb)  
汞(Hg)  
镉(Cd)  
相机本体  
×
:表示该有毒有害物质在该部件所有均质材料中的含量均在电子信息产品中有毒有害物质的  
限量要求标准规定的限量要求(SJ/T11363-2006)以下  
×示该有毒有害物质至少在该部件的某一均质材料中的含量超出电子信息产品中有毒有害物  
质的限量要求标准规定的限量要求(SJ/T11363-2006)  
This information is applicable for People's Republic of China only.  
リサイクルに関する情報(包装物)  
有关再利用的信息(包装物)  
Information on recycling of wrapping composition  
内部緩衝材料  
内部缓冲材料  
箱/箱子Box  
Internal buffer materials  
CB  
段ボール  
OTHERS  
瓦楞纸板  
Corrugated cardboard  
D4153659A  
 
1. Overview  
This GiantDragon B/W series is an integrated-(one-body)-type monochrome camera that adopts all pixel data  
readout inter line CCD. There are 4 models according to the sensor type. These are CSGV90BC3 (VGA),  
CSGX36BC3 (XGA), CSGS20BC2 (SXGA: 1/2 type), CSGU15BC18 (UXGA), and CSGS15BC23 (SXGA: 2/3  
type). For video output, the Gigabit Ethernet®* interface standard “IEEE802.3ab” is adopted for high transfer rate,  
and it is easy to integrate into industrial equipment.  
* Ethernet® is a registered trademark of XEROX Corporation.  
2. Features  
! High frame rate and high resolution  
Supported high frame rate CSGV90BC3 (90fps/VGA), CSGX36BC3 (36fps/XGA), CSGS20BC2  
(20fps/SXGA: 1/2 type), CSGU15BC18 (15fps/UXGA), and CSGS15BC23 (15fps/SXGA: 2/3 type).  
! All pixel readout  
All pixel signals (in the effective area) are output in one frame processing.  
! Full frame shutter  
Since all pixels are output even by shutter operation, high resolution can be achieved, without deteriorating  
the vertical resolution.  
! Square grids  
The CCD pixels arrayed in square grids facilitates computation for image processing.  
! Gigabit Ethernet interface  
Performs video output and camera control via the Gigabit Ethernet standard IEEE802.3ab interface. Data  
transfer is at 1Gbps that can output uncompressed video data of high frame rate.  
! GigEVision Ver 1.0 conformity  
This product is based on GigEVision Camera Interface Standard for Machine Vision Ver 1.0 that is industrial  
camera standard. Therefore, control of this camera is easy.  
! GenICam Ver 1.0 conformity  
This product is based on GenICam Generic Interface for Cameras Ver 1.0 that is industrial camera standard.  
Therefore, control of this camera is easy.  
! Binning mode  
This mode realizes high-speed frame rate by adding two vertical lines or four vertical lines.  
1
D4153659A  
 
! Random trigger shutter  
The random trigger shutter function provides images in any timing by input of an external trigger signal.  
Trigger control from PC is possible.  
! Scalable  
Selectable video output area. It can be higher frame rate by reducing vertical output area. And can be reduce  
occupied data rate of Gigabit Ethernet by reducing horizontal output area.  
! Compact and lightweight  
This camera is compact and lightweight, and it is easy to integrate into industrial equipment.  
! EU RoHS & Chinese ROHS compliant  
3. Configuration  
(1) Camera body ············································1  
(2) Accessories  
-Instruction Manual (Japanese) ··················1  
-Instruction Manual (English) ····················1  
* No application software is attached to this camera.  
4. Optional part  
(1) Camera mounting kit··································Model name: CPT8420  
(2) Camera cable·············································Model name: CPRC3910-**  
(3) Camera adapter··········································Model name: CA130C  
* Contact your dealer / distributor for details of option units.  
2
D4153659A  
 
5. Explanation rear panel  
(1) Ethernet  
Gigabit Ethernet Interface connector  
- Connector model  
- Pin assignment  
P65-P01-19V8 (Supplied by SpeedTech Corp.)  
Pin No.  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
Function  
BI_DA+  
BI_DA-  
BI_DB+  
BI_DC+  
BI_DC-  
BI_DB-  
BI_DD+  
BI_DD-  
(1)  
(2)  
1
2
3
4
5
6
7
8
LED1  
Rear View  
LED1 indicates the state of ACT.  
LED2  
- Indication LED1: GREEN (ACT LED)  
During transfer:  
Lighting  
- Indication LED2: YELLOW (LINK LED)  
During Link:  
LED2 indicates the state of LINK.  
Lighting  
* LINK LED indicates establishment of Link of 1000BASE. Therefore, in the case of 100BASE/10BASE,  
LINK LED does not light.  
(2) DC_IN / TRIGGER  
- Connector (Camera side)  
HR10A-7R-6PB(73)  
(Supplied by HIROSE ELECTRIC CO., LTD.)  
HR10A-7P-6S(73)  
- Plug (Cable side)  
(Supplied by HIROSE ELECTRIC CO., LTD.)  
or equivalents  
* This camera cable is not an accessory of this product.  
- Pin assignment  
Signal Name  
Pin No.  
[Standard specification]  
BUSY_OUT  
GND  
1
3
6
4
1
2
3
4
5
6
2
5
GND  
TRIG_IN  
EXPOSE_OUT  
+12V  
*Above figure is connector view from insert side.  
3
D4153659A  
 
6. Connection  
Connect this camera as shown in the figure below.  
(The figure below shows an example of connection. For details, contact our sales representative.)  
Option  
CameraCable  
CPRC3910-**  
Option  
CameraAdapter  
CA130C  
TRIGGER  
HD  
VD  
CAMERA  
CCDCamera  
GiantDragon  
(Rear-side)  
AC100VIN  
WEN  
VIDEO OUT CLOCK OUT  
CA130C  
TYPE2232A5900  
SERIAL
AC100V0.15A  
AC100V  
50/60Hz  
LAN Cable  
Twist-pair  
Category5e or over  
PC  
GigabitEthernet  
interfaceboard  
Notes on Connection:  
- If your camera is used in a system where its connectors are subjected to strong repetitive shocks,  
its connectors are possible to break down. If you use your camera in such a situation, use an  
LAN cable with a lock screw, and secure the camera cable as close as possible to the camera  
body for avoid physical shock to the camera connector.  
- Since the Optional parts and Gigabit Ethernet interface board, cable not attached to this product,  
please prepare it if necessary.  
4
D4153659A  
 
7. Functions  
Control and setting of functions can be done by the camera control based on the Gigabit Ethernet digital camera  
protocol (GigEVision Ver.1.00).  
(1) Image output  
A format of the output image and frame rate which this GiantDragon B/W series supports is as follows.  
Model  
CSGV90BC3 CSGX36BC3 CSGS20BC2 CSGU15BC18 CSGS15BC23  
GVSP_PIX_MONO8: Mono 8 bit  
Image output format  
GVSP_PIX_MONO10:Mono 10 bit  
Frame rate  
Maximum  
90fps  
Maximum  
36fps  
Maximum  
20fps  
Maximum  
15fps  
Maximum  
15fps  
(at the all pixel readout)  
Notes on Frame Drops of Image:  
- Depends on your PC or Gigabit Ethernet interface board configurations, images may not be  
captured normally (e.g. frame drops may occur). In this case, change to frame rate setting  
lower.  
(2) Setup-level setting  
You can set the Setup-level in 192 steps in the range between 6.3 and 25%.  
(3) Gain setting  
When shipping it, the gain is set to 0dB. You can set the gain in 91 steps in the range between 0 and +12dB.  
(4) Binning mode  
This mode realizes high-speed frame rate by adding two vertical lines or four vertical lines.  
CSGV90BC3 CSGX36BC3 CSGS20BC2 CSGU15BC18 CSGS15BC23  
Binning mode  
1/2  
240  
1/2  
384  
1/2  
480  
1/4  
300  
1/2  
512  
Readout vertical line number  
Maximum frame rate  
170fps  
64 fps  
34fps  
46fps  
32fps  
(5) Image resending control  
As the resending control of the image, this camera resends the packet which suffered a loss.  
5
D4153659A  
 
(6) Electronic shutter mode switching  
You can switch the shutter modes by adjusting the setting value of the command status register of the  
camera via the Gigabit Ethernet. The setting method has two kinds of the following.  
- Normal shutter  
Performs exposure control via the internal synchronization signal.  
PRESET mode  
1/100, 1/250, 1/500, 1/1,000, 1/2,000, 1/4,000, 1/10,000  
and 1/20,000s  
Absolute value setting  
Any value is set up in 32-bit floating point form within the range  
of 1/20000s to 2s  
- Random trigger shutter:  
Random trigger shutter can capture images at any timing using the external trigger signal and soft trigger  
input. It is effective for image input of moving objects and obtaining images of the same timing using  
multiple cameras. But there is an exposure delay time.  
The random trigger shutter of this camera can be operated in two types of mode. How to determine the  
exposure time differs depending on the mode.  
Fixed mode:  
The exposure time depends on the normal shutter speed setting.  
The exposure time depends on the pulse width.  
Pulse width mode:  
Notes on long exposure:  
- When you set the exposure time longer than approximately 1 second, white spots and the  
unevenness in highlight portion might occasionally be observed on screen. This phenomenon  
is due to the characteristics of the CCD image-pickup device, and do not reflect performance  
error in the pickup device or CCD Camera itself.  
6
D4153659A  
 
(7) Scalable mode  
This camera has the scalable mode that can read out defined area of the screen. Only continuous rectangle  
units can be selected, concave or convex shape cannot be selected.  
- Window size:  
{A x m(H)} x {B x n(V)}  
* A and B are minimum unit size.  
* m, n=integer  
* The image of maximum unit size or less can be selected.  
* Only one window can be selected.  
CSGV90BC3  
CSGX36BC3  
CSGS20BC2  
CSGU15BC18 CSGS15BC23  
Minimum unit size  
(H) x (V)  
160 x 120  
256 x 192  
160 x 120  
200 x 150  
170 x 128  
Maximum unit size  
(H) x (V)  
640 x 480  
1024 x 768  
1280 x 960  
1600 x 1200  
1360 x 1024  
- Start address:  
* i, j=integer  
{32 x i(H)} x {24 x j(V)}  
* The image of maximum unit size or less can be selected.  
(X, Y) = (32 x i, 24 x j)  
A x m  
In the scalable mode, this camera reads out only the necessary portions at the standard speed while it scans  
through other unnecessary portions at high speed, so the trigger interval can be shorter if the vertical cutout  
width is small. However, the trigger interval cannot be short in the horizontal direction even if the cutout  
width is small due to the operation mechanism of the CCD sensor.  
Notes on scalable mode:  
- White lines may occur in the upper portions of the screen when strong light exists in a wide area  
during the scalable mode. This is not a malfunction. If white lines occur, adjust the amount of  
incident light using the lens.  
7
D4153659A  
 
8. Timing chart  
Image data outputs of this camera series are transferred with the UDP protocol of Gigabit Ethernet. Timing  
numerical value below is prescribed by absolute prerequisite that GiantDragon series use transmission band  
without restriction of other node. When there is a node transferring with GiantDragon concerned, it is not same the  
numerical value prescribed below.  
(1) In the normal shutter mode  
Video format: MONO 8, all pixel readout  
Expose  
Image  
Image  
Image  
T2  
GbE bus  
T1 TDLY1  
TDLY2  
T2  
Model name  
CSGV90BC3  
CSGX36BC3  
CSGS20BC2  
CSGU15BC18  
CSGS15BC23  
T1 [ms]  
0.5  
T2 [ms]  
2.8  
Frame rate [ms]  
11.1  
27.8  
50.0  
66.7  
56.7  
0.5  
6.7  
1.0  
10.4  
16.0  
11.7  
1.0  
1.0  
* T1 is the maximum value, and T2 (GVSP_FRAME_RATE) is the minimum value.  
* Frame rate is maximum speed.  
* At the setting the GVSP_SIZE (SCPSx) = 1500 byte / packet.  
(T2 is changed by GVSP_SIZE (SCPSx).)  
* Set the value that TDLY1 (GVSP_BLOOK_START_DELAY) to satisfy the next numerical formula;  
T1 + TDLY1 + T2 >= Frame rate  
8
D4153659A  
 
(2) In the random trigger shutter mode  
- When fixed mode (Video format: MONO 8, all pixel readout);  
TRIG_IN  
T3  
Expose  
Image  
GbE bus  
T1 TDLY1  
T2  
- When pulse width mode (Video format: MONO 8, all pixel readout);  
TRIG_IN  
T3  
T4  
Expose  
Image  
GbE bus  
T1 TDLY1  
T2  
Model name  
T3 [us]  
T4 [us]  
2.8  
CSGV90BC3  
CSGX36BC3  
CSGS20BC2  
CSGU15BC18  
CSGS15BC23  
0.9  
1.5  
3.4  
1.9  
3.8  
25.2  
5.1  
7.5  
23.8  
* The value of T1 and T2 are the same as the value at the of the normal shutter setting.  
9
D4153659A  
 
9. Troubleshooting  
If any trouble occurs in use, check the following first. If the trouble persists, contact your distributor or our sales  
representatives.  
* When user confirms the troubles, please confirms the troubles on the condition that user connected the camera  
system on the smallest composition and set 1500 byte / packet to the GVSP_SIZE (SCPSx) register for  
making cause of trouble clear. About the connection of the smallest constitution, please refer to 6.Connection.  
Phenomena  
Check item  
- Check the connection of the Camera cable.  
- Check that the LINK LED(LED2) is lighting.  
If the LINK LED(LED2) is not lighting, check the connection of  
the LAN cable.  
Cannot turn on power  
- Check that the Gigabit Ethernet interface board is installed and set  
up correctly.  
Shooting image is not displayed  
- Check that the LINK LED(LED2) is lighting.  
If the LINK LED(LED2) is not lighting, check the connection of  
the LAN cable.  
- Check that the ACT LED(LED1) is lighting or blinking.  
- Check that the camera register settings are correct.  
- Check that the lens aperture is not closed.  
- Check that the Gigabit Ethernet interface board is installed and set  
up correctly.  
Frame drop occurs on shooting - If some boards are installed in the PCI slots, remove the other  
image  
boards.  
Shooting image remains still  
- Check that the camera is not in the random trigger mode.  
- Check that the ACT LED(LED1) is lighting or blinking.  
- Check that the LINK LED(LED2) is lighting.  
If the LINK LED(LED2) is not lighting, check the connection of  
the LAN cable.  
Cannot control camera from PC  
- Check that the Gigabit Ethernet interface board is installed and set  
up correctly.  
10  
D4153659A  
 
10. Specifications  
[Electrical specification]  
(1) Imager  
All-pixel-data-readout interline transfer CCD  
CSGV90BC3  
CSGX36BC3  
CSGS20BC2 CSGU15BC18 CSGS15BC23  
Number of total pixels  
(H) * (V)  
692 x 504  
659 x 494  
640 x 480  
1077 x 788  
1434 x 1050  
1392 x 1040  
1280 x 960  
1688 x 1248  
1628 x 1236  
1600 x 1200  
1434 x 1050  
1392 x 1040  
1360 x 1024  
Number of effective pixels  
(H) * (V)  
1034 x 779  
1024 x 768  
Number of Video out pixels  
(H) * (V)  
8.98 x 6.71mm2  
(2/3type)  
Scanning area  
(H) * (V)  
4.88 x 3.66 mm2 4.81 x 3.62 mm2 6.47 x 4.84 mm2 7.16 x 5.44 mm2  
(1/3 type)  
(1/3 type)  
(1/2 type)  
(1/1.8 type)  
Pixel size  
7.4 x 7.4µm2 4.65 x 4.65µm2 4.65 x 4.65µm2 4.40 x 4.40µm2  
6.45 x 6.45µm2  
(H) * (V)  
(2) Scan method  
Non-interlace  
(3) Synchronization method  
(4) Aspect ratio  
Internal synchronization  
4:3  
(5) Sensitivity  
CSGV90BC3 CSGX36BC3 CSGS20BC2 CSGU15BC18 CSGS15BC23  
600 lx  
F5.6  
800 lx  
F5.6  
500 lx  
F5.6  
400 lx  
F8  
400 lx  
F11  
Standard subject illuminance  
1/90s  
1/36s  
1/20s  
1/15s  
1/15s  
(6) Minimum subject illuminance (F1.4, GAIN Maximum, video level 50 %)  
CSGV90BC3 CSGX36BC3 CSGS20BC2 CSGU15BC18 CSGS15BC23  
Minimum subject illuminance  
2 lx  
5 lx  
7 lx  
4 lx  
1.5 lx  
(7) Gain  
0 to +12 dB (91step)  
initial factory setting: 0 dB  
OFF (γ= 1.0 fixed)  
(8) Gamma correction  
(9) Setup-level  
6.3 to 25 % (192step)  
initial factory setting: 6.3% [Approximately 16digit / 8bit]  
DC 12V +/-10% (ripple 100 mV(p-p) or less)  
3.5W Max (Maximum)  
(10) Power supply  
(11) Power consumption  
[Internal sync signal specification]  
(1) Base clock frequency  
36.0000 MHz +/- 100ppm  
11  
D4153659A  
 
Trigger signal specification]  
(1) External trigger input  
- Input level  
Low level: 0 to 0.5V  
High level: 2.0 to 5.0V  
Positive / Negative bipolar  
2us (Minimum)  
- Polarity  
- Pulse width  
- Input impedance  
(2) Software trigger  
High impedance  
Set via the Gigabit Ethernet interface  
[Output signal specification]  
(1) BUSY_OUT  
- Output level  
The period that input of the trigger signal is forbidden.  
LVTTL  
- Polarity  
Positive  
(2) EXPOSE_OUT  
- Output level  
The period that this camera exposes.  
LVTTL  
Positive  
- Polarity  
Electronic shutter specification]  
(1) Normal shutter  
- PRESET setting  
1/100s, 1/250s, 1/500s, 1/1000s, 1/2000, 1/4000,  
1/10000, 1/20000s  
- Absolute value setting  
any value is set up in 32-bit floating point form within the range  
of 1/20000s to 2s.  
(2) Random trigger shutter  
- Fixed mode  
The exposure time depends on the normal shutter speed setting.  
The exposure time depends on the pulse width.  
- Pulse width mode  
[Interface specification]  
(1) Interface system  
(2) Transmission speed  
(3) Video output  
Gigabit Ethernet IEEE802.3ab (1000BASE-T) conformity  
1Gbps (Maximum)  
depends on 7.Functions (1) Format of output image  
GigEVision Camera Interface Standard for Machine Vision  
Ver. 1.0 conformity  
(4) Protocol  
(5) Conformity Cable  
(6) Cable length  
Twist pair (Category 5e or over)  
To 100m (at the Unshielded Twist Pair (UTP) cable using)  
Oki Electric Cable Co., Ltd  
(7) Recommended cable  
HONDA TSUSHIN KOGYO CO., LTD  
High bending resistance shielded Cat5e LAN cable  
* Because above recommendation cable is high bending resistance,  
maximum length of cable is 40m.  
* Contact your dealer / distributor for details  
of recommended cable.  
12  
D4153659A  
 
Machine externals specification]]  
(1) Dimensions  
44mm(W) x 29mm(H) x 70mm(D) (Not including protrusion)  
(2) Mass  
Approximately 120g  
C-mount  
(3) Lens mount  
Notes on combination of C-mount lens:  
- Depending on the lens you use, the performance of the camera may not be brought out fully due  
to the deterioration in resolution and brightness in the peripheral area, occurrence of a ghost,  
aberration and others. When you check the combination between the lens and camera, be sure to  
use the lens you actually use. As for the C-mount lens used combining this camera, the projection  
distance from bottom of the screw should use 9.4mm or less.  
Bottom of  
the screw  
C-mount lens  
9.4mm or less  
(4) Flange back  
it is not possible to adjust it.  
(5) Camera body grounding: insulation status  
Conductive between circuit GND and camera body  
Operating Ambient conditions]  
(1) Ambient conditions  
- Performance assurance  
Temperature  
0 to 40°C  
Humidity  
10 to 90% (no condensation)  
- Operating assurance  
Temperature  
-5 to 45°C  
Humidity  
90% or less (no condensation)  
- Storage assurance  
Temperature  
-20 to 60°C  
Humidity  
90% or less (no condensation)  
(2) EMC conditions  
- EMI (Electro-Magnetic interference)  
EN61000-6-4 conformity  
FCC part15 Subpart B class A conformity  
- EMS (Electro-Magnetic susceptibility) EN61000-6-2 conformity  
Notes on Conformity of the EMC:  
- About the conformity of the EMC standard of this machine, it has guaranteed in the conditions  
combined with the option part of 4th clause.  
When used combining parts other than specification of our company, I ask you to have final EMC  
conformity checked of a visitor with a machine and the whole equipment.  
13  
D4153659A  
 
Typical spectral response]  
The lens characteristics and light source characteristics is not reflected in table.  
<CSGV90BC3>  
1.0  
0.9  
0.8  
0.7  
0.6  
0.5  
0.4  
0.3  
0.2  
0.1  
0.0  
400  
500  
600  
700  
800  
900  
Wave Length[nm]  
<CSGX36BC3>  
1.0  
0.9  
0.8  
0.7  
0.6  
0.5  
0.4  
0.3  
0.2  
0.1  
0.0  
400  
500  
600  
700  
800  
900  
1000  
Wave Length[nm]  
14  
D4153659A  
 
<CSGS20BC2>  
1.0  
0.9  
0.8  
0.7  
0.6  
0.5  
0.4  
0.3  
0.2  
0.1  
0.0  
400  
500  
600  
700  
800  
900  
1000  
Wave Length[nm]  
<CSGU15BC18>  
1.0  
0.9  
0.8  
0.7  
0.6  
0.5  
0.4  
0.3  
0.2  
0.1  
0.0  
400  
500  
600  
700  
800  
900  
1000  
Wave Length[nm]  
15  
D4153659A  
 
<CSGS15BC23>  
1.0  
0.9  
0.8  
0.7  
0.6  
0.5  
0.4  
0.3  
0.2  
0.1  
0
400  
500  
600  
700  
800  
900  
1000  
Wave Length [nm]  
16  
D4153659A  
 
11. Outline Drawing  
17  
D4153659A  
 
NOTE  
D4153659A  
 
NOTE  
D4153659A  
 
: 7-1, 4 chome, Asahigaoka, Hino-shi, Tokyo, 191-0065, Japan  
(Overseas Sales Department)  
Head Office  
Phone : +81-42-589-8771  
Fax  
: +81-42-589-8774  
Distributor  
This product must be classified for disposal according to the laws of each country and municipal laws.  
Information contained in this document is subject to change without prior notice.  
D4153659A  
 

Philips Computer Drive DVDRW228 User Manual
Philips Light Therapy Device HF3305 User Manual
Philips Work Light SORA 5 User Manual
Pioneer Stereo Amplifier GM 6400F User Manual
Poulan Pole Saw MCP1510 User Manual
Poulan Trimmer 545167665 User Manual
Poulan Trimmer 545186799 User Manual
Praktica Digital Camera D00451 User Manual
Precor Home Gym C940 User Manual
ProForm Hot Tub PFHS60070 User Manual