®
SS4718/SS4718L/SS4722/SS4722L
Sun Shroud and
TI47 Thermal Insulation
Installation/Operation Manual
C1409M-C (7/98)
1.0 WARNINGS
Prior to installation and use of this product, the following WARNINGS should be
observed.
1. Installation and servicing should only be done by qualified service personnel
and conform to all local codes.
2. Only use replacement parts recommended by Pelco.
Please thoroughly familiarize yourself with the information in this manual prior to
installation and operation.
2.0 DESCRIPTION
The information contained within this manual covers the SS4718, SS4722, SS4718L,
SS4722L Sun Shrouds and the TI47 Thermal Insulation Kit installation.
The SS4718, SS4722, SS4718L, and SS4722L Sun Shrouds provide an air space
between the sun shroud and the enclosure to protect the enclosure from the direct
rays of the sun and reduce the internal temperature by approximately 10 to 15°F
(-12.2° to -9.4°C).
The TI47 Thermal Insulation Kit provides an improved resistance to heat loss through
the body of the enclosure by adding a 1/4-inch thick polyurethane insulation to the
majority of the internal surfaces.
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
3.2.2 Body Insulation
Installation
1. Remove the long, 1.5-inch wide, strip of insulation for the side panel from the
lid insulation pad.
2. To adjust the length of the insulation pad (or the side panel), tear the insulation
along the perforations from the end(s) of the pad to fit either the 18-inch ver-
sion or the Legacy® version of the enclosure.
3. Position the pad around the press nuts in the center of the body by folding the
pad along its length. Position the insulation punch-out(s) to closely match the
position of the press nuts.
4. Remove the adhesive backing, and carefully lay the insulation in the body of
the enclosure, pressing firmly, taking care not to crease the insulation.
5. Then apply the side strip to the side of the enclosure body that does not con-
tain the “T-slot”. (See Figure 3.)
6. The insulation is very soft and will conform as needed during the installation of
the camera and lens.
7. Snap the gas spring ball joint to the lid, and close the enclosure.
3.2.3 Temperature
Specifications
Standard EH4700/EH4700L enclosure operating temperature: -10° to 120°F (-23°
to 48.8°C).
Temperature increase inside enclosure with heater operating:
17°F (9.5°C) increase with vent grills installed.
25°F (13.8°C) increase with vent covers and TI47 thermal insulation installed.
35°F (19.4°C) increase with vent covers, TI47 thermal insulation and WD47
defroster installed.
Figure 3. Installation of TI47 Thermal Insulation
Pelco Manual C1409M-C (7/98)
3
4.0 WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X,
CC3751H-2,CC3651H-2X,MC3651H-2,andMC3651H-2Xcameramodels,whichhaveafive-
year warranty.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed
dome products.
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Sixmonthsonallpanandtilts,scannersorpresetlensesusedincontinuousmotionapplications
(that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
AllgoodsrequiringwarrantyrepairshallbesentfreightprepaidtoPelco,Clovis,California.Repairs
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
totheProductsshallnotexceedthepricepaidbytheDealertoPelcoforsuchProducts. Innoevent
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss
of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
Ifawarrantyrepairisrequired, theDealermustcontactPelcoat(800) 289-9100or(559)292-1981
to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.
Methodofreturnshipmentshallbethesameorequaltothemethodbywhichtheitemwasreceived
by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number
and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Endura and ExSite are trademarks of Pelco.
© Copyright 1998, Pelco. All rights reserved.
4
Pelco Manual C1409M-C (7/98)
|