Peerless Industries TV Mount SF 632 User Manual

Installation and Assembly:  
Universal Flat Wall Mount for 10" - 37" LCD Flat Panel  
Screens  
Models: SF 635P, SF 635P-S, SF 635, SF 635-S, SF 632P, SF 632P-S, SF 632,  
SF 632-S  
This product is UL Listed. It must be  
installed by a qualified professional  
installer.  
Features:  
• For 10" to 37" flat panel screens  
R
• Ultra-slim design holds the screen flat against the wall  
Max UL Load Capacity: 115 lb (52.2 kg)  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06  
 
Parts List  
SF 635P,  
SF 632P  
Qty Part #  
SF 635P-S, SF 635,  
SF 635-S,  
SF 632-S  
Part #  
SF 632P-S  
Part #  
SF 632  
Part #  
Description  
A wall plate  
B hook bracket  
C adapter plate  
D M5 x 12 mm screw  
E M5 x 6 mm phillips screw  
F #10 SAE washer  
G #14 x 2.5" hex head wood screw  
H Alligator® anchor  
1
1
1
2
4
4
2
2
4
4
4
4
4
4
1
095-1320  
095-1321  
095-1322  
520-1027  
520-1023  
540-9400  
095-4320  
095-4321  
095-4322  
520-1027  
520-1023  
540-9400  
095-1320  
095-1321  
095-1322  
520-1064  
520-1023  
540-9400  
095-4320  
095-4321  
095-4322  
520-1064  
520-1023  
540-9400  
5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03  
590-0097  
520-1128  
520-9402  
510-9109  
504-9012  
504-9020  
590-5005  
590-0097  
520-1128  
520-9402  
510-9109  
504-9012  
504-9020  
590-5005  
590-0097  
520-1128  
520-9402  
510-9109  
504-9012  
504-9020  
590-5005  
560-1145  
590-0097  
520-1128  
520-9402  
510-9109  
504-9012  
504-9020  
590-5005  
560-1145  
I
J
M6 x 12 mm phillips screw  
M6 x 20 mm phillips screw  
K M6 x 30 mm phillips screw  
L M4 x 10 mm phillips screw  
M M4 x 20 mm phillips screw  
N .198" ID x .313" OD x .437" H retaining spacer  
O 4 mm security allen wrench  
B
A
C
O
D
E
F
G
H
I
J
K
L M N  
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06  
3 of 8  
 
Installation to Single Wood Stud Wall  
WARNING  
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and  
components.  
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended. Based  
on its edges, draw a vertical line down the stud’s center. Place wall plate (A) on wall as a template, making sure that  
the two mounting holes are over the stud centerline. Level plate, and mark the center of the two holes. Drill two  
5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using two #14 x 2.5"  
wood screws (G) as shown.  
1
Skip to step 2 on page 6 for VESA 200 mm and 200 mm x 200 mm patterns.  
Skip to step 2 on page 7 for VESA 75 mm and 100 mm patterns.  
WARNING  
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is  
highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers  
are responsible to provide hardware for other types of mounting situations.  
A
G
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06  
4 of 8  
 
Installation to Solid Concrete or Cinder Block  
WARNING  
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete  
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid  
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-  
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to  
avoid breaking out the back of the hole when entering a void or cavity.  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware  
and components.  
Make sure that wall plate (A) is level, use it as a  
1
template to mark two mounting holes. Drill two 1/4"  
(6 mm) dia. holes to a minimum depth of 2.5" (64  
mm). Insert anchors (H) in holes flush with wall as  
shown (right). Place wall plate over anchors and  
secure with two #14 x 2.5" screws (G). Level, then  
tighten all fasteners.  
concrete  
surface  
1
H
Skip to step 2 on page 6 for VESA 200 mm and  
200 mm x 200 mm patterns.  
Drill holes and insert anchors (H).  
2
Skip to step 2 on page 7 for VESA 75 mm and  
100 mm patterns.  
A
WARNING  
H
G
• Tighten screws so that wall plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
Place plate (A) over anchors (H) and secure with screws (G).  
3
• Never tighten in excess of 80 in. • lb (9 N.M.).  
WARNING  
• Always attach concrete expansion anchors directly to  
load-bearing concrete.  
Tighten all fasteners.  
• Never attach concrete expansion anchors to concrete  
covered with plaster, drywall, or other finishing mate-  
rial. If mounting to concrete surfaces covered with a  
finishing surface is unavoidable, the finishing surface  
must be counterbored as shown below. Be sure  
concrete anchors do not pull away from concrete  
when tightening screws. If plaster/drywall is thicker  
than 5/8", custom fasteners must be supplied by  
installer.  
H
A
CORRECT  
INCORRECT  
wall plate  
concrete  
concrete  
wall  
plate  
G
plaster/  
drywall  
plaster/  
drywall  
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06  
5 of 8  
 
Attaching Adapter Plate to Screen with VESA 200 or 200 x 200 Mounting Pattern  
Note: For VESA 75 mm and 100 mm patterns, see  
followingpage.  
C
Thread M5 socket pin screws (D) to hook bracket (B)  
2
making the screws flush with bracket as shown.  
Attach hook bracket (B) to adapter plate (C) using  
four M5 x 6 mm screws (E) and #10 washers (F) as  
B
shown.  
F
E
D
WARNING  
• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not  
tightly secured, damage may occur to screen or product may fail.  
FORVESA200MOUNTINGPATTERN:  
FOR VESA 200 x 200 MOUNTING PATTERN:  
3
Choose hole pattern as shown below. Attach adapter  
plate (C) to back of screen using four M4 x 10 mm  
screws (L) as shown below.  
Choose hole pattern as shown below. Attach adapter  
plate (C) to back of screen using four M6 x 12 mm  
screws (I) as shown below.  
*Note: If screw (L) gets less than three threads of  
engagement, attach adapter plate (C) to back of  
screen using four M4 x 20 mm screws (M) and four  
spacers (N) as indicated below.  
*Note: If screw (I) gets less than three threads of  
engagement, attach adapter plate (C) to back of  
screen using four M6 x 20 mm screws (J). If screw  
(J) still gets less than three threads of engagement,  
use four M6 x 30 mm screws (K).  
Skip to step 4 on page 8.  
Skip to step 4 on page 8.  
C
*For screens with a hole  
pattern in a pocket,  
spacers (N) go between  
adapter plate (C) and  
screen.  
C
L
I
N
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06  
6 of 8  
 
Attaching Hook Bracket to Screen with VESA 75 or 100 Mounting Pattern  
Thread M5 phillips screws (D) to hook bracket (B)  
making the screws flush with bracket as shown in  
figures 2.1 and 2.2.  
2
B
B
D
fig. 2.1  
D
fig. 2.2  
WARNING  
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly  
secured, damage may occur to screen or product may fail.  
FORVESA75MOUNTINGPATTERN:  
FORVESA100MOUNTINGPATTERN:  
3
Choose hole pattern as shown below. Attach hook  
bracket (B) to back of screen using four M4 x 10 mm  
screws (L) as shown below.  
Choose hole pattern as shown below. Attach hook  
bracket (B) to back of screen using four M4 x 10 mm  
screws (L) as shown below.  
*Note: If hole pattern is in a pocket, attach hook  
bracket (B) to back of screen using four M4 x 20 mm  
screws (M) and four spacers (N) as indicated below.  
B
B
L
L
*For screens with a hole  
pattern in a pocket,  
spacers (N) go between  
hook bracket (B) and  
N
screen.  
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06  
7 of 8  
 
Installing and Removing Flat Panel Screen  
Hook screen onto wall plate (A) figure 4.1. Tighten  
M5 x 12 mm screws (D), shown in figure 4.2 and  
detail 1.  
SCREEN  
4
A
Note: For security models, use 4 mm security allen  
wrench (O) to tighten M5 x 12 mm screws (D).  
To remove screen from mount, loosen screws (D)  
and lift screen off of mount.  
WARNING  
• Do not lift more weight than you can handle. Use  
additional man power or mechanical lifting equipment  
to safely handle placement of the screen.  
• Failure to lock hook bracket with screws (D) can  
cause screen to come off mount if hit accidentally.  
CAUTION  
• Do not tighten screws with excessive force.  
Overtightening can cause damage to mount. Tighten  
screws to 20 in. • lb (2.26 N.M.) maximum torque.  
fig. 4.1  
B
A
A
B
D
D
fig. 4.2  
DETAIL 1  
ISSUED: 04-20-05 SHEET #: 201-9429-6 02-01-06  
8 of 8  
©2005PeerlessIndustries,Inc.Allrightsreserved.  
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.  
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.  
 

Philips Digital Camera MIC4014SB User Manual
Philips Digital Camera SPC535NC User Manual
Philips Digital Photo Frame SPF 3408 G7 User Manual
Philips Headphones HC 8391 User Manual
Philips Headphones SHC1300 User Manual
Philips Radio AE2630 User Manual
Polaroid Film Camera 298SL User Manual
Poulan Tiller PRRT9000 User Manual
Precor Treadmill 905e User Manual
ProForm Treadmill PFTL715053 User Manual