Specifications
Quadra® 12P
Nominal sensitivity (1 Watt @ 1 meter,
swept sine input in an anechoic
environment):
SPECIFICATIONS
Frequency response:
61 Hz to 18 kHz
100 dB
Maximum sound pressure level @
1 meter:
130 dB music peak
Low frequency limit (-3 dB point):
61 Hz
Usable low frequency limit (-10 dB point):
52 Hz
Nominal radiation angle:
90˚ horizontal by 45˚ vertical
Internal power amplifiers (@ 120 VAC
line):
Woofer — 800 Watts peak dynamic
power
400 Watts at clipping
Tweeter —200 Watts peak dynamic
power 100 Watts
Transducer compliment:
BWX Black Widow® 12" weather-
resistant woofer and RX™22 2"
titanium diaphragm compression driver
tweeter
Box tuning frequency (Fbox):
70 Hz
at clipping
Specifications
Quadra 12P
Multiple molded-in handles provide
easy transport, while multiple
switchable microphone input (female
XLR) and a Loop Out/Loop In is
The enclosure is constructed of
injection-molded 1/4" thick
mounting points on top and bottom for provided. A volume control is located
polypropylene with a UL flame rating
and internal reinforcing ribs. A
the Peavey Versamount70 and a
molded-in stand adapter allow
maximum utility.
next to the input jack group.
The system power amplifiers have
an unfiltered frequency response of
10 Hz to 30 kHz, which deviates no
more than +0, -1dB up to rated power;
a damping factor greater than 100 @
1 kHz into 4 Ohms; hum and noise
better than 90 dB below rated power;
and THD and IMD of less than 0.1%.
The woofer amplifier is capable of
handling 400 Watts into a 4 Ohm
nominal load, and the tweeter
amplifier is capable of 100 Watts
output into a 6 Ohm load. Both
incorporate independent SPS
handgrip is molded into each side of
the woofer and on the top rear edge.
A vinyl-coated, perforated metal
grille provides woofer protection. The
cabinet incorporates four tall, sturdy
rubber feet for floor standing use and
four mounting-point inserts on the top
and bottom, each for flying use.
The outside dimensions are 23-
11/16" high by 17-13/16" wide by
13-3/4" deep, and the unit weighs
55 lbs. Power requirements: maximum
660 Watts, nominal 180 Watts,
120VAC, 60 Hz domestic and 240 VAC,
50 Hz (European).
ARCHITECTURAL AND ENGINEERING
SPECIFICATIONS
This powered loudspeaker system
has a frequency response from 62 Hz
to 18 kHz. The peak SPL with inaudible
distortion will reach 130 dB when
measured at a distance of 1 meter and
driven to full output capacity. The
system utilizes a 12" BWX Black
Widow woofer and an RX22
compression driver tweeter. The
nominal radiation pattern is 90˚ in the
horizontal plane and 45˚ in the vertical
plane.
compression.
The input signal is electronically
divided into high frequencies and low
frequencies by a staggered pole, third
order slope line-level crossover at
1.8 kHz. The low frequencies are
processed to provide bass boost,
3 + 2 YEAR LIMITED WARRANTY
NOTE: For details, refer to the
warranty statement. Copies of this
statement may be obtained by
contacting Peavey Electronics
The powered, bi-amplified
loudspeaker system has a group of
medium impedance input connectors
consisting of one combo female XLR, a
1/4" RTS phone jack and one male XLR
on the rear panel, all connected in
parallel. Additionally, a separate,
subsonic filtering and overall response Corporation, P.O. Box 2898, Meridian,
shaping, and the high frequencies are
equalized for constant directivity horn
EQ and response shaping.
Mississippi 39301-2898.
Specifications
Quadra 12P
80305044
Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301
©2002
Printed in the U.S.A. 5/02
|
Peavey Music Mixer 1000 SM User Manual
Pelco TV Mount MR3050 User Manual
Pentair Network Card BB HCM311A User Manual
Philips Work Light Reflector Lamps User Manual
Pioneer Stereo Receiver SC 09TX User Manual
Pioneer Stereo Receiver VSX D638 G User Manual
Poulan Chainsaw 530164284 User Manual
ProScan Flat Panel Television PLDED3273A User Manual
PYLE Audio Car Stereo System PLTDN70 User Manual
PYLE Audio Car Video System PLCM4200 User Manual